Victor Nakoryakov
231 linhas
6.5 KiB
ReStructuredText
231 linhas
6.5 KiB
ReStructuredText
|
|
Quick start
|
|
===========
|
|
|
|
Learn how to work with ino in few minutes.
|
|
|
|
Creating a project
|
|
------------------
|
|
|
|
Let's create a simple project::
|
|
|
|
$ mkdir beep
|
|
$ cd beep
|
|
$ ino init -t blink
|
|
|
|
Here we've created a new directory for our project and initialized project
|
|
skeleton with ``ino init`` command. We chose to use *blink* as a project
|
|
template. That will create a simple sketch for LED blinking on pin 13.
|
|
Lets see what we've got::
|
|
|
|
$ tree
|
|
.
|
|
├── lib
|
|
└── src
|
|
└── sketch.pde
|
|
|
|
$ cat src/sketch.pde
|
|
|
|
#define LED_PIN 13
|
|
|
|
void setup()
|
|
{
|
|
pinMode(LED_PIN, OUTPUT);
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
digitalWrite(LED_PIN, HIGH);
|
|
delay(100);
|
|
digitalWrite(LED_PIN, LOW);
|
|
delay(900);
|
|
}
|
|
|
|
Here we have two directories. ``src`` is a source directory where we can
|
|
put our project's ``*.[c|cpp|pde|h|hpp]`` source files. ``sketch.pde``
|
|
was created for us, so we have a starting point. ``lib`` is a directory
|
|
where we may put 3-rd party libraries if we would want.
|
|
|
|
Building
|
|
--------
|
|
|
|
Lets build it::
|
|
|
|
$ ino build
|
|
Searching for Board description file (boards.txt) ... /usr/local/share/arduino/hardware/arduino/boards.txt
|
|
Searching for Arduino core library ... /usr/local/share/arduino/hardware/arduino/cores/arduino
|
|
Searching for Arduino standard libraries ... /usr/local/share/arduino/libraries
|
|
Searching for Arduino lib version file (version.txt) ... /usr/local/share/arduino/lib/version.txt
|
|
Detecting Arduino software version ... 22
|
|
Searching for avr-gcc ... /usr/bin/avr-gcc
|
|
Searching for avr-g++ ... /usr/bin/avr-g++
|
|
Searching for avr-ar ... /usr/bin/avr-ar
|
|
Searching for avr-objcopy ... /usr/bin/avr-objcopy
|
|
Scanning dependencies of src
|
|
src/sketch.cpp
|
|
arduino/wiring_shift.c
|
|
arduino/wiring.c
|
|
arduino/WInterrupts.c
|
|
arduino/wiring_digital.c
|
|
arduino/wiring_pulse.c
|
|
arduino/wiring_analog.c
|
|
arduino/pins_arduino.c
|
|
arduino/HardwareSerial.cpp
|
|
arduino/WString.cpp
|
|
arduino/main.cpp
|
|
arduino/Print.cpp
|
|
arduino/WMath.cpp
|
|
arduino/Tone.cpp
|
|
Linking libcore.a
|
|
Linking firmware.elf
|
|
Converting to firmware.hex
|
|
|
|
Whew! A lot of work has been done behind the scenes for a single command.
|
|
It's at most about finding necessary tools and directories, and compiling
|
|
the standard core library. Actually you shouldn't care. The consequence
|
|
is that we've got ``firmware.hex``—ready to upload binary file.
|
|
|
|
Uploading
|
|
---------
|
|
|
|
Lets upload it::
|
|
|
|
$ ino upload
|
|
Searching for stty ... /bin/stty
|
|
Searching for avrdude ... /usr/local/share/arduino/hardware/tools/avrdude
|
|
Searching for avrdude.conf ... /usr/local/share/arduino/hardware/tools/avrdude.conf
|
|
|
|
avrdude: AVR device initialized and ready to accept instructions
|
|
|
|
Reading | ################################################## | 100% 0.00s
|
|
|
|
avrdude: Device signature = 0x1e950f
|
|
avrdude: reading input file ".build/firmware.hex"
|
|
avrdude: writing flash (428 bytes):
|
|
|
|
Writing | ################################################## | 100% 0.08s
|
|
|
|
avrdude: 428 bytes of flash written
|
|
avrdude: verifying flash memory against .build/firmware.hex:
|
|
avrdude: load data flash data from input file .build/firmware.hex:
|
|
avrdude: input file .build/firmware.hex contains 428 bytes
|
|
avrdude: reading on-chip flash data:
|
|
|
|
Reading | ################################################## | 100% 0.06s
|
|
|
|
avrdude: verifying ...
|
|
avrdude: 428 bytes of flash verified
|
|
|
|
avrdude: safemode: Fuses OK
|
|
|
|
avrdude done. Thank you.
|
|
|
|
Again, quite much output, but the job is done. Arduino flashes with its
|
|
buil-in LED on pin 13.
|
|
|
|
Serial communication
|
|
--------------------
|
|
|
|
OK, now lets deal with serial communication a bit. With editor of your choice change
|
|
``src/sketch.pde`` to::
|
|
|
|
void setup()
|
|
{
|
|
Serial.begin(9600);
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
Serial.println(millis());
|
|
delay(1000);
|
|
}
|
|
|
|
This should transmit number of milliseconds spent from power up every second via
|
|
serial port. Lets build it::
|
|
|
|
$ ino build
|
|
Scanning dependencies of src
|
|
src/sketch.cpp
|
|
Linking firmware.elf
|
|
Converting to firmware.hex
|
|
|
|
As you can see much fewer of steps have been performed behind the scenes. It is
|
|
because only things that have been changed are taken into account. This boosts
|
|
up the build.
|
|
|
|
Lets upload it with ``ino upload``. When uploading is done lets connect to the
|
|
device with serial monitor to see what it prints::
|
|
|
|
$ ino serial
|
|
Searching for Serial monitor (picocom) ... /usr/bin/picocom
|
|
picocom v1.4
|
|
|
|
port is : /dev/ttyACM0
|
|
flowcontrol : none
|
|
baudrate is : 9600
|
|
parity is : none
|
|
databits are : 8
|
|
escape is : C-a
|
|
noinit is : no
|
|
noreset is : no
|
|
nolock is : yes
|
|
send_cmd is : ascii_xfr -s -v -l10
|
|
receive_cmd is : rz -vv
|
|
|
|
Terminal ready
|
|
0
|
|
1000
|
|
2004
|
|
3009
|
|
4014
|
|
|
|
That's what we want! Press Ctrl+A Ctrl+X to exit.
|
|
|
|
Tweaking parameters
|
|
-------------------
|
|
|
|
All examples were done in assumption that you have Arduino Uno and it is
|
|
available on default port. Now consider you have Arduino Mega 2560 and
|
|
it is available on port ``/dev/ttyACM1``. We have to specify this for
|
|
our build steps as command-line switches.
|
|
|
|
Board model may be set with ``--board-model`` or ``-m`` switch. Port
|
|
is set with ``--serial-port`` or ``-p`` switch. So lets do it::
|
|
|
|
$ ino build -m mega2560
|
|
$ ino upload -m mega2560 -p /dev/ttyACM1
|
|
$ ino serial -p /dev/ttyACM1
|
|
|
|
It can be annoying to provide these switches over and over again. So
|
|
you can save them in ``ino.ini`` file in project directory. Put
|
|
following lines to the ``ino.ini``::
|
|
|
|
[build]
|
|
board-model = mega2560
|
|
|
|
[upload]
|
|
board-model = mega2560
|
|
serial-port = /dev/ttyACM1
|
|
|
|
[serial]
|
|
serial-port = /dev/ttyACM1
|
|
|
|
Now you can build, upload and communicate via serial not having to provide
|
|
any parameters. Well, in most cases if you build for Mega 2560, you will
|
|
want to upload to Mega 2560 as well. The same about serial port setting.
|
|
So to don't repeat settings for different commands shared switches could
|
|
be moved up to an unnamed section. So having just following lines in ``ino.ini``
|
|
is enough::
|
|
|
|
board-model = mega2560
|
|
serial-port = /dev/ttyACM1
|
|
|
|
Furthermore, if you have Mega 2560, it is likely that you have it for all
|
|
projects you make. You can put a shared configuration file to either::
|
|
|
|
1. /etc/ino.ini
|
|
2. ~/inorc
|
|
|
|
And it'll be used for setting default parameter values if they're not
|
|
overriden by the local ``ino.ini`` or by explicit command-line switches.
|